NXP Zigbee JN516X JN517x JN518X 用vsCode studio 环境开发编译
NXP Zigbee JN516X JN517x JN518X 用vsCode studio 环境开发编译前言
官方推荐是用Beyond IDE开发，不方便,搭建开发环境,安装插件基本不是成功的。
i have a problem to install the plugin Zbee pro configuration editorwith sdk JN-4141
the version of beyond studiois : Build 1308sdk jn 4170 is : Build Number 1745I've reinstalled it twice in the default path and on D drive, and it still doesn't work.when i install the plugin (ZB pro configuration edition 2.0.0), i have the message error :Cannot complete the install because one or more required items could not be found.Software being installed: NXP ZBPro Configuration Editor 2.0.0 (com.jennic.sdk.zbpro.external.feature.feature.group 2.0.0)
Missing requirement: ZBPro Config Edit Support 2.0.0 (com.jennic.zps.configeditor.edit 2.0.0) requires 'bundle org.eclipse.emf.edit 0.0.0' but it could not be found
Cannot satisfy dependency:
From: NXP ZBPro Configuration Editor 2.0.0 (com.jennic.sdk.zbpro.external.feature.feature.group 2.0.0)
To: com.jennic.zps.configeditor.edit
以上摘自NXP社区,碰到这样问题的用户非常多, 我也碰到, 于是想到用VSCODE。
准备
安装visual code studio(microsoft官网下载, 安装过程过于简单不再赘述)
安装EIDE插件
下载SKD（JN516x---JN-SW4170，Jn517x---JN-SW-4270) 安装后， 复制到NXP_JN工作目录(比如E:\bstudio_nxp\workspace)，不用要中文， 路径不能太深。
具体方法,请参考：【ZigBee 系列】|NXP-JN5169 ZigBee 3.0 开发环境搭建及编译-谷动谷力 (sunsili.com)
下载NXP Zigeeb工程源码示例
( 参考： NXP Zigbee JN5169 软件开发流程-SDK下载 及 AN 介绍与 ..., 有链接 下载 相关的例程)
如下：
Coordinator：适合应用场景：网关。JN-AN-1216-Zigbee-3-0-IoT-ControlBridgeJN-AN-1217-Zigbee-3-0-Base-Device
Router：适合应用场景：长供电应用，例如各类灯应用、插座。JN-AN-1218-Zigbee-3-0-Light-BulbJN-AN-1217-Zigbee-3-0-Base-Device
End Device：适合应用场景：低功耗休眠应用、各类传感器应用、开关控制器，例如温湿度传感器、烟雾报警器等。JN-AN-1219-Zigbee-3-0-Controller-and-SwitchJN-AN-1220-Zigbee-3-0-SensorsJN-AN-1217-Zigbee-3-0-Base-Device
Test Code：适用于测试射频参数，功耗等硬件指标。JN-AN-1172-JN516x-Customer-Module-Evaluation-Tool
更多内容请参阅：NXP Zigbee JN5169 软件开发流程-SDK 及 AN 介绍与选择-谷动谷力 (sunsili.com)
实战操作
解压 源码JN-AN-1219\JN-AN-1219-Zigbee-3-0-Controller-and-Switch到NXP_JN工作目录(比如E:\bstudio_nxp\workspace)，不用要中文， 路径不能太深。与在刚才SDK存放在同一目录。方便修改Makefile SDK 相对路径。
在“资源资源管理器” -右键“用vsCode打开”
或用vsCode“文件”-“打开文件夹” 打开JN-AN-1219\JN-AN-1219-Zigbee-3-0-Controller-and-Switch文件夹
打开Eide msys bash 终端
到子工程目录下的build 下
输入命令：
make JENNIC_CHIP=JN5169 JENNIC_CHIP_FAMILY=JN516x REMOTE=ColorSceneController DR=DR1199 TRACE=1 all
或修改Makefile
#User definable make parameters that may be overwritten from the command line
选择芯片型号系列 板型 SDK
# Default target device is the JN5179
JENNIC_CHIP ?= JN5179#芯片型号
JENNIC_CHIP_FAMILY ?= JN517x #系列
ifeq ($(JENNIC_CHIP_FAMILY),JN517x)
ENDIAN ?= LITTLE_ENDIAN
endif
ifeq ($(JENNIC_CHIP_FAMILY),JN516x)
JENNIC_SDK ?= JN-SW-4170
JENNIC_PCB ?= DEVKIT4
else
ifeq ($(JENNIC_CHIP_FAMILY),JN517x)
JENNIC_SDK ?= JN-SW-4270
JENNIC_PCB ?= DEVKIT5
endif
修改工程名（目标）# Application target name
TARGET = EH_Switch #工程名
CFLAGS += -DPDM_USER_SUPPLIED_ID
CFLAGS += -DPDM_NO_RTOS
CFLAGS +=-DEH_Switch
PDM_BUILD_TYPE = _EEPROM
CFLAGS += -DPDM$(PDM_BUILD_TYPE)
修改Makefile
定位好SDK、工程路径（没配置好，编译会报错）
# Use if application directory contains single target
SDK_BASE_DIR = $(abspath ../../../../sdk/$(JENNIC_SDK))
APP_BASE = $(abspath ..)
APP_BLD_DIR = $(APP_BASE)/Build
APP_SRC_DIR = $(APP_BASE)/Source
APP_COMMON_SRC_DIR = $(APP_BASE)/../Common/Source
MMAC_DIR = $(APP_BASE)/../../Components/MMAC/Include
LIB_DIR = $(APP_BASE)/../Components/Library
ZIGBEE_COMMON_SRC = $(COMPONENTS_BASE_DIR)/ZigbeeCommon/Source
make clean
编译前先clean
make clean
编译
输入编译命令
make -j8(8线程，只要电脑支持线程多，比IDE编译快多了）
JN-AN-1907... Makefiles配置
TARGET = JN-AN-1907-Zigbee-Valve-Controller-JN5169
DEV_TYPE = ValveController
#Note: Target name must be the same as the subfolder name
##############################################################################
#User definable make parameters that may be overwritten from the command line
# Default target device is the JN5148
JENNIC_CHIP ?= JN5169
##############################################################################
# Default DK2 development kit target hardware
JENNIC_PCB ?= DEVKIT4
##############################################################################
# Select the network stack (e.g. MAC, ZBPRO)
JENNIC_STACK ?= MAC
##############################################################################
# Debug options define DEBUG for HW debug
#DEBUG ?=HW
#
#
# Define which UART to use for debug
DEBUG_PORT ?= UART1
##############################################################################
# Define TRACE to use with DBG module
TRACE ?= 1
##############################################################################
# Define configuration
ifeq ($(FLOW_CONTROL), NO_FLOW_CONTROL)
CFLAGS+= -DENABLE_NO_FLOW_CONTROL
BIN_SUFFIX = _NO_FLOW_CTRL
endif
ifeq ($(FLOW_CONTROL), HW_FLOW_CONTROL)
CFLAGS+= -DENABLE_HW_FLOW_CONTROL
BIN_SUFFIX = _HW_FLOW_CTRL
endif
ifeq ($(FLOW_CONTROL), HW_SW_FLOW_CONTROL)
CFLAGS+= -DENABLE_HW_SW_FLOW_CONTROL
BIN_SUFFIX = _HW_SW_FLOW_CTRL
endif
##############################################################################
##############################################################################
##############################################################################
# Path definitions
# Select definitions for either single or multiple targets
# Use if application directory contains multiple targets
SDK_BASE_DIR = $(abspath ../../../sdk/JN-SW-4163)
LZSTACK_BASE_DIR = $(abspath ../../..)
APP_BASE = $(abspath ../..)
APP_BLD_DIR = $(APP_BASE)/$(DEV_TYPE)/Build
APP_SRC_DIR = $(APP_BASE)/$(DEV_TYPE)/Source
APP_COMMON_SRC_DIR = $(APP_BASE)/Common/Source
JENOS_DIR = $(LZSTACK_BASE_DIR)/LZStackV5/JenOS
STACK_DIR = $(LZSTACK_BASE_DIR)/LZStackV5/stack
STACK_MAC_DIR = $(LZSTACK_BASE_DIR)/LZStackV5/stack/mac
STACK_NWK_DIR = $(LZSTACK_BASE_DIR)/LZStackV5/stack/nwk
STACK_ZDO_DIR = $(LZSTACK_BASE_DIR)/LZStackV5/stack/zdo
STACK_APS_DIR = $(LZSTACK_BASE_DIR)/LZStackV5/stack/aps
STACK_COMMON_DIR = $(LZSTACK_BASE_DIR)/LZStackV5/common
页:
[1]